We recommend that you view our assemble video, before you start assemble your JumpXfun.

 

 

STEP 1
The top frame must be adjusted to fit exactly to your trampoline. The legs of the JumpXfun should be right next to the legs of your trampoline, and as close to the legs as possible.

 

 

 

 

 

 

 

STEP 2
The tubes must be pushed into each other so that the downward poles stick straight out of every leg on the trampoline, and as close to the trampoline’s legs as possible. The top frame should form a square.

The top of JumpX must be adjusted so the legs of JumpX are as close to the legs of the trampoline as possible.

 

 

 

 

 

 

STEP 3
Assembly 19 to the corner Parts 1. The Lock nut must be stuck tight.

 

 

 

 

 

 

 

STEP 4
Refer to the below diagrams to fix the Pulley block at the end of rope 17. The short rope (17) (5 metre) is used down to the winch, onto the Pulley block.
After cutting, treat the end of the rope with fire to prevent fraying

 

 

 

 

 

 

 

STEP 5
The long rope (16) (15 metre) is used at the top. Refer to the below diagrams to load the rope 16 into the pulley block.

 

 

 

 

 

 

 

STEP 6
Refer to the below diagrams to fix the swivel at the end of rope 16.

Adjust the length of the cord, to fit your trampoline. You must be able to lift the jumper all the way to the top, (22) all the way up to (19). You may have to shorten the cord.

After cutting, treat the end of the rope with fire to prevent fraying.

 

 

 

 

STEP 11 + 12
Mount 8 pieces of foam (A) on the 4 long tubes and mount them under the 4 corners. Run the foam (A) down so it covers from the top edge of the trampoline and two metres up.

The short tubes (5) must only be used if you have a trampoline with legs of 70-90 cm. If you have an in-ground trampoline, you must not use short tubes (5).

Plastic feet (25) should be put under the short tubes (5). If you have an in-ground trampoline, the plastic feet should be put under the long tubes (4) (See step 10)

 

 

STEP 13
Assembly of hand winch set.

The winch must be mounted so the handle is on the right side. It should be mounted between the ground and the frame of the trampoline, so you can easily turn the handle. The cover must be put on, fasten it with screws.

 

 

 

 

 

STEP 14
Bottom of the winch needs to be at least 57cm above the ground.

 

 

 

 

 

STEP 15
Fit the legs of JumpX to the trampoline legs with 8 pieces Big U-screw (10), 2 pieces on each leg, as high and as low as possible. If not, adjust the top of JumpX so the legs of JumpX are as close to the legs of the trampoline as possible. There must be a minimum of 40 cm distance between the two Big U-screw (10). The greater the distance the better. All fittings must be tightened well (when the trampoline is buried, the distance must be between the fittings should be minimum 20 cm.) When you have a trampoline with 3-5-7 legs, you can only attach the JumpXfun two legs to the trampoline’s 2 legs, the other 2 to be mounted on the trampoline edge, with a double bracket.

 

 

 

 

 

STEP 17
Refer to the below diagrams to fix the Harness. It can be dangerous not to raise the jumper all the way up, and not to have enough rubber tubes on it. here have to be so many rubber tubes on, so that the jumper cannot reach the trampoline’s dew with its head.

CAUTION! In order to avoid moisture and sun damage to the harness and rubber tubes, store indoors when JumpX is not being used. Note that sun, rain, snow, and extreme temperatures can affect the parts’ durability.

Movement of JumpX JumpX should be disassembled before moving it over longer distances. For shorter moves it should be lifted from the ground by 4 people and kept horizontal during transport.